Jump to content

PRO9-TL quarter-wave Transmission Line Loudspeakers


Recommended Posts

Item Condition: Used
Shipping Options: Pickup available and you can audition.
Suburb or Town: Ferndown
Payment Method: PayPal or Cash on Pickup
Reason for selling: Upgrade

I am reluctantly selling a pair of original Chris Rogers PRO9-TL quarter-wave transmission line loudspeakers finished in teak wood veneer.  These are the actual speakers that have featured in many of my reviews for Hi-Fi Choice magazine over the years. Based on the original Rogers’ design from Practical Hi-Fi and Audio, October 1976, these speakers have been significantly upgraded over the years with new Audax HD12 tweeters fitted with Russ Andrews’ Focus Rings and new Peerless K040-MRF midrange, all replaced recently.  The switches of the crossovers have been removed and then completely rebuilt with audiophile components throughout, including ClarityCap polypropylene capacitors, Mills audio grade resistors, and Mundorf 99% silver/1% gold wiring.  I am finally selling them as I needed to get some smaller speakers!

 

The cabinets are in good condition for their age.  The teak veneer has bubbled slightly in places but has been well looked-after with wax and teak oil. Collection only from Ferndown in Dorset.

 
Photos attached.

 

PRO9TL Crossover.JPG

PRO9TL1.jpg

PRO9TL2.jpg

PRO9TL3.jpg

  • Like 2
  • Love 1
Link to comment
Share on other sites

I built a pair of these many years ago and regret selling them…… I needed the money 😂

fantastic sound and a great bottom end.

fabulous price

 

GLWS

Link to comment
Share on other sites

Fantastic looking and great sounding speakers.

 

Many years ago I had Chris demonstrate his pair to me with his SIRAC Amp, but I remembered a different tweeter, a KK8 sticks in my mind.

 

If they had been in Australia I would have bought them without a doubt.

 

GLWS

 

Ken

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Similar Content

    • By Baz W
      Item Condition: Near Mint Shipping Options: Shipping is available at agreed cost. Suburb or Town: Gold Coast State: QLD Payment Method: Paypal, EFT Reason for selling: NLR Further information: Some are imported and now hard to get. Will combine with my other blues posting.



    • By Baggio
      Item Condition: Great Condition Shipping Options: Pickup available but audition is not available. Suburb or Town: West Pennant Hills State: NSW Payment Method: Paypal, EFT, Cash on Pickup Reason for selling: Upgrading Further information:
      One of the best enthusiasts 7 x channel x 200 watts into 8 power amplifiers available.
      Only ever been used for rear effects with mono blocks used for front channel. In absolutely brand new like condition. This is still the current model, with an optional XD upgrade being the only difference.
      As an added bonus, the unit will also come with a DanA carbon fiber base which provides added sound insulation. It also has wheels underneath to help push the 45kg power amp forwards & backwards when required for access behind and a more stable floor base.
      See the following URL for further detail about the features of the unit: https://www.krellhifi.com/products/chorus-7200-xd-multi-channel-amplifier/
       
      Photos:











    • By Janjuggler
      Item Condition: Very Good ++ Shipping Options: Pickup available but audition is not available.,Shipping is available at agreed cost. Suburb or Town: TORQUAY State: VIC Payment Method: Paypal (Friends + Family) or +3%, Cash, EFT + Post Reason for selling: Upgrading System Further information:
       
      Well regarded Turn Table from European Audio Team, EAT C-SHARP (Currently selling for $6499)
       
      Separate Power supply and speed controller, does not come with cartridge.
       
      With Carbon Fibre and Termoplastic Elastomer, Eat was designing a new superflat table. The low profile base chassis is made out of highest density MDF. Because of its flatness this base sits perfectly stable on any surface! On this base the ultra low noise motor is mounted as well as 10 damping feets out of energy absorbing TPE (Thermoplastic Elastomers = Hightech high energy absorbing damping material). The cone shape TPE columns carry a SANDWICH sub-chassis out of Carbon Fibre and MDF composite with ultimate rigidity.
      The stiffness is important to be a super rigid base for the tonearm/cartridge and bearing/platter as there must be 100 % no moving tolerance between the distance of the groove and the tracking cartridge. All the rumble of the platter / bearing is directed in the TPE columns. On opposite the TPE avoid that any unwanted energy of motor and surface or surrounding vibration leads to the sub-chassis or even to the tonearm cartridge.
      The bearing is an oversized inverted with a inert, resonance free ceramic ball on top Around the bearing we set a super heavy 700g mass point which sucks up all energy around.The stiff carbon sub-chassis helps to transport all vibration in this mass point. So vibrations are transferred in heat The platter itself is from a special alloy of very inert aluminium and is also damped by TPE inserts-It from 2 parts a sub-platter and a main platter to keep it flat although having very high mass and kinetic energy.
      The belt is made from special anti-static rubber. It's glued and then polished.
      The tonearm itself is a completely new design which combines all advantages of a unipivot arm with a Cardan design. The uni-pivot in the middle only helps bearing to be less loaded. The traditional Cardan bearing insures high stability and easiness of use with very low friction. Also inside the tonearm is a special silicon-based grease to damp the tonearm / cartridge resonances by more then 50%
      The tube is again out of carbon , super stiff and rigid. The headshell we made out of special light and rigid aluminium to get a perfect combination of the advantages of carbon with the better inner damping of the aluminium as well as the possibility of more tighter mounting of Highend MC cartridges.
      An external DC power supply unit with an AC Generator creates new total clean power for the motors . You have also 33 /45 electronic switching.
       
      EAT C-SHARP TURNTABLE TECHNICAL INFORMATION
      NOMINAL SPEED    33/45 rpm, driven by microprocessor, separate control panel, lighted control buttons
      SPEED VARIANCE    33 rpm: ± < 0,08%, 45 rpm: ± < 0,09%
      SIGNAL TO NOISE    S/N Ratio ( mechanical noise): – 40 dB, Signal to noise (electrical noise): -70 dB
      DOWNFORCE RANGE    0 – 30 mN
      SUPPLIED COUNTERWEIGHTS    without additional insert =>for cartridge 5 – 9g (125g)
      EFFECTIVE TONEARM MASS    16.5 g
      EFFECTIVE TONEARM LENGTH    254 mm
      OVERHANG    16 mm
      POWER CONSUMPTION    8,5 W max / 0,5 W standby
      VOLTAGE    Universal switch mode power supply 15 V DC / 1,6 A, 90-264 V AC, 47 – 63Hz
      DIMENSIONS (W × H × D)    500 × 400 × 115mm without connectors, 500 × 435 × 115mm with connectors in the rear panel
      WEIGHT (WITHOUT BOX)    13,5 kg + 0,5 kg Separated control panel
       
       
      Reviews : 
       
      https://www.theabsolutesound.com/articles/eat-c-sharp-turntable-with-ortofon-quintet-black-cartridge/
       
      https://hifipig.com/eat-c-sharp-turntable-and-koetsu-black-mc-cartridge/
       
      https://trueaudiophile.com/eat-turntable-c-sharp-the-reviewers-table/
       
      https://6moons.com/audioreviews/grado2/sonata1.html
       
      Photos:
       












       
      JJ




    • By Mikety
      Item Condition: Brand-new Shipping Options: Pickup available and you can audition.,Shipping is available at agreed cost. Suburb or Town: Sydney State: NSW Payment Method: EFT, PayPal + plus fee Reason for selling: Surplus Further information:
       
      Weiduka AC8.8 10way 3000W 15A, support most of plugs as US, AU, EU, British.
       
      Advance version with LCD display table headers that shows both voltage and current.
       
      Condition: new in box.
       
      2 are available for sale, one black, one silver.
       
      Postage available at buyer's cost.

      Photos:
       
       




    • By Donald Trump
      Item Condition: Excellent, one tiny mark on ear cup. Shipping Options: Shipping is included in price. Suburb or Town: Yarra Ranges State: VIC Payment Method: Paypal, EFT, Cash on pick up Reason for selling: Lack of time to use them. Further information:
       
      Barely used Beyerdynamic Aventho headphones. Includes all original accessories. Made in Germany.
       
      This is the wired version with an in-line microphone.
       
      Less than an hour of use. Purchased on impulse, beautiful sound but no time to use them unfortunately.
       
      There is a tiny mark on one of the ear cups, I've tried to capture this in the photos below.
       
      RRP $499.
       
      Photos:
       






       




×
×
  • Create New...
To Top