Jump to content

SOLD: FS: Musical Fidelity M6Si Amplifier


SHF Staff
 Share

Recommended Posts

SOLD
Item Condition: Good Secondhand Condition
Shipping Options: Pickup available and you can audition.,Shipping is available at agreed cost.
Suburb or Town: Castle Hill
State: NSW
Payment Method: EFT, Cash and Card
Reason for selling: Retailer

Further information:  Just Traded this Musical Fedility M6I aside from some scratches on the front and top is in excellent condition.

Internally, the M6si is configured as 2 independent monobloc power amps with a separate pre amp. It is, in fact, a pre amp with 2 monobloc power amps that just happen to share the same casework.

The M6si has 220wpc. It has very low distortion, outstanding noise ratio and extremely flat frequency response. Its inputs are phono (MM/MC), 4 line level, 1 balanced XLR and 1 USB ‘B’ up to 24bit 96kHz asynchronous.

The M6 combination of high power, high current and extraordinary stability means that it can drive any loudspeaker with ease.

In use it is hard to hear any practical difference between the M6si and other much more expensive amplifiers. In proper blind listening comparisons, the M6si performs incredibly well. If we sound rather enthusiastic it’s because we are.

M6si In Brief

·         220WPC

·         Excellent technical performance

·         Amazing load driving ability, unconditional stability will drive any loudspeaker

·         Wide range of useful inputs including asynchronous USB and switchable MM / MC Phono

·         Preamp output

·         Internally it is a separate preamp with two independent monobloc power amps; effectively a separates system in a box

·         Excellent, hunky build quality

M6si - Specifications

Amplifier

Power output: 220 Watts per channel into 8 Ohms

THD (+ noise): <0.007 % typical 20Hz - 20 kHz

Signal to Noise Ratio: >107dB ‘A’ - weighted

Frequency Response: +0, –0.1dB, 10Hz to 20 kHz

Inputs

4x Line Level RCA

1x Line Level XLR Balanced

1x USB type ‘B’ connector - asynchronous data stream at up to 24-bit/96kHz

1 x switchable phono input

Trigger in

Phono Input

Sensitivity: 3mV nominal (MM), 0.4mV nominal (MC)

Signal / noise ratio: >84dB ‘A’-weighted

Input impedance: 47k Ohms (MM and MC)

Frequency response: RIAA/IEC ±0.5dB 20Hz-20kHz

Outputs

Trigger out

Fixed, line level output

Variable, preamp output

General

Dimensions - WxHxD (mm): 440 x 125 x 400

Weight (unpacked / packed): 16.6 kg/ 21.3 kg

 

Comes with remote and power cable, no original box or manual

IMG-3893.thumb.jpg.8637dd2668b0ca40c1a0a555088fe534.jpgIMG-3891.thumb.jpg.a62e31355733bdecb2c8c9ca7dd259fa.jpgIMG-3892.thumb.jpg.fb24889d9fa145c179e7048531e72ffa.jpgIMG-3890.thumb.jpg.b31d0319bb4b55ebc5ab9b44bf44e397.jpgIMG-3889.thumb.jpg.5d782ccf2304ad5368f2fcac58181e66.jpgIMG_3886.thumb.JPG.f241e7a1e3b0caf249ef16a178e3b1d9.JPG

Edited by SHF Staff
  • Like 5
Link to comment
Share on other sites


Guest
This topic is now closed to further replies.
 Share





×
×
  • Create New...
To Top